SUPER X-SIM : RSS Products Feed :: PROGRAMMER http://www.gsmdevice.org/ en Copyright (c) 2009 WALZ CO. sales@alibababox.com (WALZ CO.) sales@alibababox.com (WALZ CO.) Wed, 10 Jun 2009 09:27:48 +0000 Zen-Cart v. v 2.1.4 14.02.2008 15:26 RSS 2.0 Feed 1440 LAB-TOOL 48 http://www.gsmdevice.org/labtool-48-p-4499.html http://www.gsmdevice.org/index.php?main_page=product_reviews&products_id=4499 LAB-TOOL 48LT - 48 UNIVERSAL PROGRAMMER
For more than 5000 kinds of IC programming, included phones memory


Description

Feature

The LT- 48 is a universal device programmer which works through your PC's parallel port. It features a 48-pin universal pin driver. It supports over 3000 different devices including PAL, GAL, CEPAL, CPLD, EPLD, PEEL, MAX, MACH, pLSI, microprocessors, EPROM, Serial PROM, PROM and Flash memory.
Supports all GSM/CDMA/GPRS phone's memory to read & write ,direct to repair problem phones.
Support memory/cpu/pal and about more than 3000 device.
48-pin ZIF with device insert/contact check
Auto-sense/Self programming with statistical report (for mass production)
No adapter required for DIL chip up to 48-pin guarantee
Support 3.3 V low voltage chips
Program 16-Mbit Flash within 120 seconds
Support Windows 3.x, Windows 95/98/me/2000 and DOS, free lifetime software upgrade
Universal 48-pin BGA, 44-pin PLCC, 40-pin TSOP, 44-pin PSOP and 48-pin TSOP 56-pin TSOP adapters

Universal pin driver--True universal programming
The MOSFET logic controls the programmer's pin switches, so each pin can supply Vcc, Vpp or ground. Pins can also be configured for TTL high/low levels with pull-high/pull-low, high-speed clock and tri-state. This advanced pin design lets you program any DIP device up to 48 pins without an adapter. It also ensures support for the full range of silicon technologies on the market--today and tomorrow.

Unbeatable programming speed
The LT-48's on-board intelligence reduces system overhead to a minimum. The LT48 can program an 8-Mbit EPROM in less than 100 seconds. (The actual throughput depends slightly on the processing power of your PC; the above time was with a 486DX2-66 processor.) The LabTool-48 is much faster than its competitors, making it much more productive with today's high-density, multi-megabit memory devices.

Device insertion and contact checks--No mistakes!
The LT48 performs device insertion and contact checks before it programs each device. It can detect poor pin contact and devices inserted upside down or in the wrong position. This function protects your pocketbook by preventing expensive chip damage due to operator error.

EPROM and Flash memory ID detection
Many EPROMs and Flash memories have a burnt-in device ID and manufacturer ID. The LT48 can read the device's ID to determine its vendor and product number. This feature is especially useful with second-user chips and devices that have had their part number accidentally (or intentionally!) removed.

Auto-sensing and self-programming
To meet mass-production requirements the LT-48 has implemented new patented technology in both its hardware and software. After entering the Mass-production Mode, the production line operator inserts a device into the ZIF socket. An LED on the LT-48 will indicate the device is programmed successfully and the operator simply removes it and replaces it with a new one. No formal training is necessary adding flexibility and saving time and money. In addition, the LabTool-48's auto-sensing feature ensures the device has been inserted correctly and then automatically programs the device. Furthermore, in the mass-production mode the system keyboard is automatically disabled preventing the operator from making any inadvertent mistakes.

Memory buffer auto Increment
If your memory devices need individual serial numbers, the LT-48 has an Auto Increment function, This simply increments the serial numbers in the buffer each time a new device is inserted. This saves time and money. The LT-48 has everything you need in one package: 48-pin driver, socket and complete device support library. You don't need to order separate device libraries.

User-selectable verify voltage, one- or two-pass verification
The LT48 lets you select the verify voltage after you have programmed the device, e.g., 5 V, 5 V ?%, 5 V ?0%. This feature ensures that your device has been programmed properly, preventing failures due to programming errors and ensuring data retention.

Easy operation--Get to work immediately
The programming software's easy-to-use graphical interface eliminates your learning curve--you don't need the manual! Like MS-Windows, the software offers pop-up dialog
boxes and on-line help. You can simply type the device vendor's name and part number. The software will select the proper driver automatically; you don't need to search one by
one through long lists of devices.

Project file save option
You can save a configuration project file which contains the device select, the buffer data and all the programming setup options, This file can be called upon at any time for future use without having to go through the setting up procedure again.

Non-DIP device support through versatile converters
The LT48's universal pin driver capability lets it program all 48-pin DIP devices without DIP-to-DIP adapters, including all single-chip microcontrollers. The market, however, offers many choices besides DIP devices, such as PLCCs, SOPs, TSOPs, QFPs and SDIPs. We have developed over 40 different converters to support these special-package devices. The LT-48's universal pin driver significantly reduces the number of converters required, reducing your cost for future expansion. For example, a single 44-pin PLCC adapter lets it program all 44-pin PLCC devices.

File format conversion
JEDEC, POF, Binary, Intel HEX, Intel EXT HEX, Motorola S and HP 64000ABS

System requirements

Operating system:
DOS Version: DOS 3.1 or higher (or Windows DOS prompt)
Windows Version: Windows 3.x, Windows 95/98/ME/2000
Processor: 386, 486, Pentium or Pentium Pro
4 MB RAM minimum, 8 MB recommended
Hard disk with 8 MB free space
Parallel port interface

General

Power: 100 to 240 VAC, auto-switching
Freq. range: 47 to 63 Hz
Power consumption: 25 W
Operating temperature: 5 to 45¡ãC (41 to 113¡ãF)
CE Certified


Device Support Summary

ALi: Microcontroler
Altera: MAX Series, Classic PLD, Serial PROM.
AMD: MACH Series, PAL, up, Bipolar PROM, EPROM, Flash.
ATMEL: ATV Series, ATF/AT PLD, AT89xx/90xx, Serial PROM, EPROM, Flash.
Cypress: CY7C3xx, PLD, Bipolar PROM.
Fujitsu: EPROM, Flash.
ICT: CPLD, PEEL, Serial PROM.
Intel: IFX, PLD, 87xx, EPROM, Flash.
Lattice: pLSI/ispLSI, GAL.
Macronix: EPROM, Flash.
Microchip: PIC, Serial PROM.
Motorola: 68 Series uP.
NS: GAL, COP, Serial PROM, Bipolar PROM, EPROM.
Philips: CPLD, PLUS/PLS, 87xx.
STMicroelectronic: GAL, ST62xx, EPROM, Flash.
SHARP: Flash.
SST: Flash.
TI: TIBAL, TMS320, TBP, EPROM, Flash.
Winbond: W78Exx, EPROM, Flash.
WSI: PSD3xx/4xx, Bipolar PROM, EPROM.
Xilinx: XC7000/9000 Series, Serial PROM.
Zilog: Z86xx.

Device Support in Detail
You can also find the support device lists by clicking following items:

All,
Complex PLD,PLD, PAL, GAL, CEPAL,
Single Chip Microprocessor,
Bipolar & CMOS PROM,
E/EEPROM & Flash,
Download the most update LabTool-48 software for a trial.

Packages included

CD-rom with the software, user manual


Buy Now ]]> sales@alibababox.com (WALZ CO.) http://www.gsmdevice.org/labtool-48-p-4499.html Mon, 25 May 2009 17:45:26 +0000 300.00 USD 4499 2.7 Walz Co. 5000 PG051002 http://www.gsmdevice.org/images/v/_picture.gif UP-48 http://www.gsmdevice.org/up48-p-4500.html http://www.gsmdevice.org/index.php?main_page=product_reviews&products_id=4500 UP-48

- Feature
Embed high speed CPU.
Ultra-high programming speed. Programs 28F320B3 in less than 30 seconds, and Verifys it less then 11 seconds.

48 ZIP universal drivers. No adapter is needed for DIP chips48,No family PACK is needed for any package. Universal DIP, PLCC, QFP, TSOP, PSOP, SOIC, SSOP, SDIP, uBGA, CSP adapters up to 48 pins. Device specific adapters up to 100 pins are available.

0.7V-25.5V/256 levels drivers voltage.

Support FLASH,EPROM,EEPROM,MCU,PLD.

Test TTL/COMS and SRAM.

Device insertion and poor-pin-contact check protect chip from destroyed. Over-current protection protects pin-drivers from damaged. And display with graphical interfaces.
Surge check and protect within 1MS.

Auto-run mode starts programming automatically upon detection of chip insertion.

The software support Windoes 98/ME/NT/2000/XP.

- More option:

Reload and save buffer.

Verify after read.

Prompt the Lock bits after change devices.

Alarm before Program/Erase/Lock.

Automatic find EEPROM devices.

more ...

- System requirements

Operating system:
Windows Version:98/98SE/ME/NT/2000/XP
Processor: Pentium or Higher
16 MB RAM minimum, 32 MB recommended
Hard disk with 8 MB free space
USB port interface

- General

Power: 100 to 240 VAC, auto-switching
Freq. range: 47 to 63 Hz
Power consumption: 25 W
Operating temperature: 5 to 45¡ãC (41 to 113¡ãF)
CE Certified
　



Buy Now ]]> sales@alibababox.com (WALZ CO.) http://www.gsmdevice.org/up48-p-4500.html Mon, 25 May 2009 17:45:26 +0000 300.00 USD 4500 2.5 Walz Co. 988 PR-0410009 http://www.gsmdevice.org/images/v/_picture.gif LabTool-48XP Intelligent Universal Programmer http://www.gsmdevice.org/labtool48xp-intelligent-universal-programmer-p-4501.html http://www.gsmdevice.org/index.php?main_page=product_reviews&products_id=4501 LabTool-48XP Intelligent Universal Programmer

Features

Printer-port interface with auto-switch power

Support 5V and 3.3V low voltage devices, 1.8V chip support through low voltage adapter.

Less then 2 seconds per M bit Programming speed for high density flash chip.

No adapter required for DIL chip up to 48-pin

48-pin universal pin driver and current limit

Auto-sense/ Self programming with statistical report Device insertion /continuity check

Universal adapter for 44-pin PLCC/ QFP/ TQFP/PSOP and 40/48 TSOP

Supports Windows 95/98, Windows 2000, windows XP and NT

 Automatic EPROM/ Flash ID search

?Serialization for Memory/μP chip

?Memory buffer H / L byte swap

?Project file save / load function

?User-selectable verify Vcc with one or two-pass verify voltage

?Automatic file format detection and conversion

   User-changeable programming parameters

   Pin swapping table provided for all adapters

   3 years warranty

   Software update via web

Universal pin driver--No adapter required for DIL devices

The LabTool-48XP features universal pin driver, each pin can supply four different voltage, ground, it also can be configurable as TTL high/low levels with pull-high/pull-low, high-speed clock and high impedance. This advanced pin design lets you program any DIL device of up to 48 pins without needing an adapter.

Unbeatable programming speed

The LabTool-48XP's on-board intelligence reduces system overhead to a minimum. The LabTool-48XP has 100% more performance then its predecessor product in program the high density flash chip, it can program a Intel 32 M bit flash chip in less then 60 seconds.

 Intel 28F320C3B
 AMD 29DL323DB
?br />Blank check
?18.6 sec
?18.9 sec
?br />Program
?57.5 sec
?76.2 sec
?br />Verify
?32.5 sec
?33.0 sec
?br />Total?
?108.6 sec
?128.1 sec
                  

The LabTool-48XP is much faster than its competitors, making it much more productive with today's high density, multi-megabit memory devices.

Technological innovation and performance leadership

Device insertion and contact checks--No mistakes!

The LabTool-48XP performs device insertion and contact checks before it programs each device. It can detect poor pin contact and devices inserted upside down or in the wrong position. This function protects your pocketbook by preventing expensive chip damage due to operator error.?

EPROM and Flash memory ID detection and Search

Many EPROM and Flash memories have a build-in device ID and manufacturer ID. The LabTool-48XP can read the device's ID by press hot key to detect the ID and compare its database and determined the chip?s correct vendor and product number. This feature is especially useful with secondhand chips and devices that have had their part number accidentally (or intentionally) removed (this function only applied to 28 pin or 32 pin EPROM and Flash).?

Auto-sensing and self-programming

To meet mass-production requirements the LabTool-48XP has implemented new patented technology in both its hardware and software. After entering the Mass-production Mode, the production line operator inserts a device into the ZIF socket. An LED on the LabTool-48XP indicates the device is ready and the operator simply removes it and replaces it with a new one. No formal training is necessary adding flexibility and saving time and money. In addition, the LabTool-48XP's auto-sensing feature ensures the device has been inserted correctly and then automatically programs the device. Furthermore, in the mass-production mode the system keyboard is automatically disabled preventing the operator from making any inadvertent mistakes.

Project file save and load

User can create and save a project file which contains device selection, buffer data and all the programming set-up options, this project file can be called upon at any time for future use without having to go through the setting up procedure again, your design file can easily pass to production department without making any mistake.

Serialization function

If your memory devices need individual serial numbers with different increment sequence and initial value, the LabTool-48XP has an Auto Increment function. This simply increments the serial numbers in the buffer each time a new device is inserted. This saves time and money.

User-selectable verify voltage, one or two-pass verification

The LabTool-48XP lets you select the verify voltage after you have programmed the device, e.g., Vcc, Vcc ?%, Vcc ?0%. The Vcc voltage can be 2.0V to 6.5V. This feature ensures that your device has been programmed properly, preventing failures due to programming errors and ensuring data retention.?

Non-DIL device support through versatile converters

The LabTool-48XP's universal pin driver capability lets it program all 48-pin DIL devices, including all single-chip Micro-controllers, without DIL-to-DIL adapters. However there are many different packages beside DIL package, such as PLCC, SOP, TSOP, QFP and SDIP. We have developed over 100 different adapters to support these special-package devices.

3 Year warranty and software update via web

The LabTool-48XP has additional safety features such as a built-in current limit and pin continuity check function. This prevents damage from faulty chips during the programming cycle. As a result we have provided a 3 year warranty on parts and labor for the LabTool-48 XP(limited 50,000-cycle warranty on ZIF socket). Free software updates are also available via web at www.aec.com.tw.  

Universal 44-pin PLCC, QFP, PSOP and TQFP adapter supports 44-pin chips

The universal pin driver on the LabTool-48XP enables you to support all 44-pin chips such as EPLD, EPROM, Flash, EPLD and Micro-controllers. You need only one 44-pin universal adapter which eliminates the need to buy multiple adapters and saves money. Moreover, different package devices within 48 pins will only require one adapter.

Pin swapping table-Build the adapter yourself

The LabTool-48XP provides all adapter pin swapping tables you need (no active components) via web at www.aec.com.tw/products/adapters.pdf. You can simply download the relevant table and build the adapters by yourself if necessary , this will arrive saving valuable time and money.  ?

Low voltage chip support
The LabTool-48XP support 2.0V ~ 5.0V logic level input/output, and it can supply 2.0V~21V analog voltage (such as VCC). Support lower then 2.7V low voltage chip such as 1.8V also possible by special low voltage adapter on top of its 48 pin ZIF socket.

Specifications

Socket and pin driver

●   48-pin DIL/ ZIF socket with receptacle for 8-pin to 48-pin 300/ 600-mil devices.

●   Four DACs for Vcc, Vpp1, Vpp2 and Vpp3 with 8-bit resolution. Software controllable rises time and current limit protection.

●   Logic driver supports pull-up/ pull-down or high impedance on all 48 pins with 2.0V-5V level.

   Device support

   Memory : PROM, EPROM, EEPROM, Flash, Serial PROM, NVRAM

●   Logic: PAL, GAL, CEPAL, PEEL, CDLD, EPLD,

●?Others: OTP/Flash Micro-controllers?

Device operations

Read, blank check, device insertion/ contact check, verify, checksum, EPROM ID check, compare, erase chip, function test, program, memory protect, device configuration setting, device search, edit buffer, mass production mode, modify vector, serialization, H/L byte buffer swap, buffer search.

PLD vector tester

●   Accepts JEDEC test vectors up to 48 pins

●   2500V/usec. rise time

●  ?File format conversion

●   JEDEC, POF, Binary, Intel HEX, Intel EXT HEX, Motorola S, HP 64000ABS, Straight Hex and TEKTRONIC Hex, Automatic detection and conversion.?

PC system requirements

●   Operating system: Windows 95/98, Win 2000, Windows XP or Windows NT

●   Processor: 386 and above

●   8 MB RAM minimum, 32 MB recommended

●   Hard disk with 16 MB free space

●   Parallel port with EPP mode

●   CD ROM driver?

       General

●   Power: 100 to 240 VAC, auto-switching

●   Frequent range : 47 to 63 Hz

●   Power consumption : 25 W

●   Operating temperature: 5 to 45 ℃ (41 to 113℉)

●   CE & LVD certified

●   Weight 1.8KG



Buy Now ]]> sales@alibababox.com (WALZ CO.) http://www.gsmdevice.org/labtool48xp-intelligent-universal-programmer-p-4501.html Mon, 25 May 2009 17:45:26 +0000 780.00 USD 4501 1.8 Walz Co. 992 PR-05061301 http://www.gsmdevice.org/images/v/_picture.gif PIC PRIGRAMMER http://www.gsmdevice.org/pic-prigrammer-p-4502.html http://www.gsmdevice.org/index.php?main_page=product_reviews&products_id=4502 PIC PRIGRAMMER

This is Special PIC programmer, it is for all new pic MCU, PIC16FXX, PIC16FXXX, PIC16FXXXA, PIC12CXXX, PIC12CEXXX, PIC16CXX, PIC16CXXX, PIC18FXXX....

You can use this special programmer to program DIV dongle, Sagem v14 dongle, Sagem SCDR II dongle, Prodigy dongle and all other dongle that use PIC MCU...

It is use in PC LPT port, support WIN 98, NT and XP.



Buy Now ]]> sales@alibababox.com (WALZ CO.) http://www.gsmdevice.org/pic-prigrammer-p-4502.html Mon, 25 May 2009 17:45:26 +0000 80.00 USD 4502 1.1 GsmDevice 988 PR-05061801 http://www.gsmdevice.org/images/v/_picture.gif IC-PROG PROGRAMMER http://www.gsmdevice.org/icprog-programmer-p-4503.html http://www.gsmdevice.org/index.php?main_page=product_reviews&products_id=4503 IC-PROG PROGRAMMER

Descriptions

This is special programmer for PIC IC programming.

Support

PIC12F629 PIC16C620APIC12F675PIC16C61PIC16C621A
PIC16C622PIC16C63PIC16C622APIC16CE623PIC16CE624
PIC16CE625PIC16C621PIC16C62APIC16C62BPIC16C620
PIC16C505PIC16C433PIC16F630PIC16F676PIC16C63A
PIC16C64APIC16C65APIC16C65BPIC16C66PIC16C67
PIC16C71PIC16C710 PIC16C711 PIC16C712PIC16C715
PIC16C716 PIC16C72PIC16C717PIC16C72APIC16F72
PIC16F73 PIC16F74 PIC16F76 PIC16F745 PIC16C73A
PIC16C73B PIC16C76 PIC16C77PIC16C765 PIC16C773
PIC16F77 PIC16C74A PIC16C74BPIC16C774 PIC16F871
PIC16F818PIC16F819 PIC16F872 PIC16F870 PIC16F874A
PIC16F83 PIC16F84 PIC16F84A PIC16F873 PIC16F873A
PIC16F874 PIC16F877A PIC16F877 PIC16F876A PIC18F1320
24C0124C0224C0424C0824C016
24C3224C6424C12824C25624C512



Buy Now ]]> sales@alibababox.com (WALZ CO.) http://www.gsmdevice.org/icprog-programmer-p-4503.html Mon, 25 May 2009 17:45:26 +0000 60.00 USD 4503 0.2 GsmDevice 987 PR-05070401 http://www.gsmdevice.org/images/v/_picture.gif